For licensed electricians and electrical contractors

An electrical estimate
built around code, load and clarity.

Break down 200A panel swaps, AFCI/GFCI breakers, wire gauges, permit coordination, and drywall exclusions so bids get approved without back-and-forth.

Free to use - No signup - PDF + PNG

What you send

A one-page proposal clients actually read.

  • Panel & breaker detail. Specify ampacity, copper busbars, grounding rods, and surge protection cleanly.
  • Materials separated from labor. Separate 6/3 Romex, panel gear, and conduit from electrician hours.
  • Utility & permit readiness. Note utility disconnect scheduling and NEC inspection milestones upfront.
  • Clear wall-patching boundaries. State upfront that electrician cuts for fishing wire are patched by others.

Proposal

Your Business

#4821

Prepared for David Kowalski

Project 200A main panel upgrade + garage 50A EV circuit

200A copper-bus main breaker panel + grounding upgrade × 1$1480.00
Garage 240V / 50A EV circuit run (6/3 NM-B + NEMA 14-50) × 1$690.00
Licensed master/journeyman electrical labor × 8$1120.00
Total$3290.00
Open the editor with this template

Pre-filled — just change names and prices.

Field Standard • On-Site Audit

Pre-Bid Electrical Load & Panel Walkthrough

Verify service ampacity, busbar space, grounding electrodes, and concealed wiring paths before quoting electrical work.

0 / 6 On-Site Checks Verified
  • NEC Article 220 Service Load Calculation

    Measure existing service size (100A vs. 200A) and calculate continuous HVAC, range, dryer, and EV charger demand before promising circuit capacity.

  • Panel Brand & Recall Screening

    Inspect load center for obsolete/recalled panels (Federal Pacific Stab-Lok, Zinsco, Challenger) requiring full replacement before adding branch circuits.

  • Grounding Electrode & Bonding Verification

    Confirm presence of two 8-ft copper ground rods, cold-water pipe bond, and gas-pipe CSST bonding per current NEC standards.

  • AFCI / GFCI Code & Wire Type Check

    Check interior walls/attic for ungrounded cloth wire, aluminum branch wiring, or knob-and-tube circuits before quoting dimmer or fixture swaps.

  • Wall Fishing vs. Drywall Access Paths

    Identify fire-blocking, spray-foam insulation, or finished two-story ceilings where clean wire fishing requires small access cutouts.

  • Utility Disconnect & Meter Clearance Coordination

    Verify meter height/clearance and local utility power shutoff fees or scheduling windows for service-entrance mast and panel swaps.

Technical Benchmarks • Zero Hidden Markups

Job Costing & Material Estimation Standard

NEC wire ampacity math, breaker allocations, and licensed electrical labor benchmarks.

Copper Branch Conductor Footage + Slack

(Horizontal Run + Vertical Panel/Drop Height) × 1.15 Termination & Routing Buffer

Worked Example: 40 ft EV run + 12 ft vertical = 52 ft × 1.15 = 60 ft 6/3 AWG copper

EV Charger Continuous Load Breakers (NEC 125%)

Max Continuous Charging Amps × 1.25 = Minimum Breaker & Wire Ampacity

Worked Example: 40A continuous EV charger × 1.25 = 50A 2-pole breaker & 6 AWG copper

Trade Task / ScopeStandard Labor OutputMaterial Coverage / WastePrep & Complexity Factor
200A Main Breaker Panel Replacement & Grounding8.0 – 11.0 crew hrs1 load center + 2 ground rods + surge+3.5 hrs if meter base or mast riser replacement required
Dedicated 240V / 50A EV Charger Circuit3.0 – 5.5 hrs+15% 6/3 AWG copper & conduit waste+2.5 hrs if unfinished trenching or subpanel required
Recessed LED Canless Downlights (Room Batch)1.2 – 1.8 hrs / fixture+10% 14/2 NM-B wire buffer+50% for finished 1st-floor ceiling under 2nd-floor bath
Whole-Home Type 2 Surge Protector Install1.0 – 1.5 hrs1 SPD device + 2-pole breakerRequires open 2-pole bus space at panel top
Scope Clarity • Dispute Prevention

Common Quoting Ambiguities vs. Transparent Alternatives

Replace vague electrical line items that trigger surprise charges or unpaid rework with clear, measurable scope language.

Dispute Trigger / Scope AreaAmbiguous Quote Wording (Avoid)Why It Causes DisputesTransparent Quote Alternative (Use This)
200A Panel Scope & Grounding Code
Upgrade house electrical panel to 200 amps — $3,200
Leaves meter socket replacement, copper ground rods, cold-water bonding, AFCI/GFCI breakers, and surge arrestors ambiguous.

Install 200A 40-space copper-bus main breaker panel, two 8-ft copper ground rods, cold-water bond, Type 2 SPD surge protector, and labeled circuit directory. Existing meter socket retained unless utility mandates upgrade.

EV Charger Amps & Conductor Sizing
Install Tesla / EV garage outlet — $850
Cheap residential 14-50 outlets melt under 8-hour continuous 40A EV charging, creating fire hazards.

Dedicated 50A GFCI-protected 240V circuit up to 35 ft using 6/3 AWG copper conductors and industrial-grade Hubbell/Bryant NEMA 14-50 receptacle, torque-verified per NEC 110.14(D).

Wire Fishing Drywall Patching
Add 6 recessed ceiling lights cleanly
Homeowners assume holes cut across ceiling joists to route 14/2 Romex will be textured and repainted at zero cost.

Includes layout, hole cutting, IC-rated LED installation, and dimmer switch. Small drywall cutouts needed to drill ceiling joists will be rough-screwed back in place; finish tape/mud/paint excluded.

Mutual Consent • Copyable Contract Terms

Fair Quoting & Scope Protection Clauses

Copy these transparent, plain-English clauses directly into your electrical proposal terms to protect both contractor and client from unforeseen defects, supply shifts, and warranty disputes.

Code Safety

Concealed Non-Compliant Wiring Discovery Protocol

HIDDEN WIRING DISCOVERY PROTOCOL: If wall opening or junction testing exposes ungrounded knob-and-tube, brittle cloth insulation, or aluminum branch circuits not visible during inspection, work on that branch will pause immediately. We will share photos and issue an NEC-compliant repair option before energizing.

Scope Clarity

Access Cutouts & Drywall Restoration Policy

ACCESS CUTS & FINISH PATCHING: Fishing cables through fire-blocked walls or finished ceilings may require neat drywall access holes. Electricians minimize cuts and keep the site vacuum-clean; finish drywall spackling, texture, and repainting are excluded unless added separately.

Fair Warranty

Torque, Testing & Workmanship Warranty Boundary

ELECTRICAL WORKMANSHIP WARRANTY: We warrant all panel terminations, grounding bonds, and branch installations against workmanship defects for 24 months. Utility grid surges, owner-supplied smart devices/luminaires, and nuisance breaker trips from faulty client appliances are excluded.

How it works

Three steps, two minutes.

01

Choose electrical scope

Load a 200A panel upgrade, EV charger run, or recessed lighting layout.

02

Set gear and labor rows

Adjust circuit counts, wire footage, permit allowances, and deposit terms.

03

Export PDF or PNG

Send crisp A4 PDFs by email or PNG images straight from the panel room.

Trade Guide

What to Include in a Compliant Electrical Proposal

Residential and light-commercial electrical proposals earn higher approval rates when they translate NEC safety requirements into plain client language. Instead of writing 'upgrade main panel — $3,400', specify the 200-amp copper-bus main breaker load center, two 8-foot copper ground rods, cold-water ground bond, whole-home Type 2 surge protector, and updated panel circuit directory.

Just as important is separating hidden framing conditions and cosmetic wall repairs. When fishing circuits through finished two-story walls or insulated ceilings, fire-blocking and joists often require small access cuts. Stating clearly that finish drywall mudding and repainting remain excluded—or quoting them as an optional add-on—prevents friction at final walkthrough.

Average Pricing & Benchmarks

Industry standard estimates (2026)

Use these typical cost baselines to price your electrical bids competitively and transparently.

Service / ScopeTypical RangeBilling Model
200-Amp Main Service Panel Upgrade$2,800 - $4,600Turnkey gear + permit + labor
Level 2 EV Charger Circuit (240V / 50A–60A)$750 - $1,650Base run + per-ft wire distance
Recessed LED Canless Downlights$160 - $260Per fixture installed
Whole-Home Surge Protector (Type 2)$350 - $600Flat material + panel tie-in

Common questions

Can I itemize AFCI/GFCI breakers and copper wire separately?

Yes — dedicate line items for main load center gear, dual-function breakers, and copper wire runs.

How should drywall access cuts from fishing wire be handled?

Clearly state under Exclusions that wire-fishing drywall cuts are minimized and rough-closed only unless finish drywall/painting is added.

Can I include utility disconnect or municipal electrical permits?

Yes — add a pass-through permit/inspection row so homeowners know city fees are billed without markup.

What happens if an EV charger install triggers a main service upgrade?

Document your NEC load calculation beforehand and include a clear note if the existing 100A panel requires a separate 200A upgrade or load-shedding device.

Is any client address or bid data stored on QuoteFast?

No — everything executes inside your local browser session with zero uploads.

Ready to send your electrical proposal?

Open the free editor — no signup. Download PDF for email or PNG for texting.

Create proposal now