Trade Prompt Pack • 4 Field-Tested Prompts

AI Prompts for HVAC Changeouts, Load Specs & Warranty Boundaries.

Copy-ready ChatGPT, Claude, and Gemini prompts for HVAC contractors to explain AHRI matching, static pressure, line-set prep, and OEM parts vs. labor coverage.

Why this prevents commercial disputes

Clients receiving a $9,000 vs. $12,500 HVAC quote rarely understand SEER2 efficiency tiers, nitrogen-purged brazing, or why OEM 10-year warranties exclude year-6 labor. These prompts turn technical craft into transparent value.

PROMPT 01 • ChatGPT / Claude / Gemini

Present an AHRI-Matched System Changeout with Full Commissioning Steps

Use Case & Commercial Purpose: Justifies quality mechanical work by itemizing equipment models, sheet-metal transitions, flood-safety float switches, and <500 micron vacuum checks.

Copy-Ready Prompt

Act as a NATE-certified HVAC estimator. Turn my changeout site notes into a clear, itemized proposal for QuoteFast.

Rules:
1. Separate AHRI-Matched Equipment, Installation Accessories (plenum, float switch, line prep), and Commissioning Labor.
2. Specify SEER2 rating, deep vacuum target (<500 microns), nitrogen-purged brazing, and EPA haul-away.
3. Explicitly exclude whole-home ductwork replacement and main electrical service upgrades unless itemized.

Inputs:
- Client Name: [Client Name]
- Equipment: [e.g., 3-Ton 16 SEER2 Split Heat Pump + Variable Air Handler]
- Accessories: [e.g., Sheet-metal plenum transitions, secondary pan + float switch, condenser pad, whip]
- Labor & Commissioning: [e.g., 12 crew hrs @ $155/hr]

Sample AI Output

HVAC SYSTEM CHANGEOUT PROPOSAL — [Client Name]
1. AHRI-Matched Equipment: $4,950.00
- 3-Ton 16 SEER2 Split Heat Pump Condenser + Variable-Speed Indoor Air Handler (registered 10-yr OEM parts warranty)

2. Fabrication, Flood Protection & Accessories: $890.00
- Custom galvanized sheet-metal plenum transitions sealed with UL-181 mastic, secondary drain pan + safety float cutoff switch, composite pad, disconnect whip, and new brazed filter drier.

3. EPA Recovery, Installation & Commissioning Labor (12 hrs @ $155/hr): $1,860.00
- EPA refrigerant recovery & unit haul-away, nitrogen-purged copper brazing, deep vacuum pull (<500 microns w/ decay hold), and subcooling/airflow verification.

Exclusions: Whole-home duct trunk replacement, asbestos remediation, and main electrical breaker panel upgrades.

Ethical & Transparency Checkpoint

Always list matched outdoor condenser and indoor coil/air-handler model families rather than vague tonnage labels.

PROMPT 02 • ChatGPT / Claude / Gemini

Compare Single-Stage Standard vs. Variable-Speed SEER2 Options Honestly

Use Case & Commercial Purpose: Helps homeowners decide between baseline efficiency and variable-speed humidity control using real price and noise differences—no sales pressure.

Copy-Ready Prompt

Create an objective 2-option HVAC comparison for [Client Name]:
- Option A (Baseline): [e.g., 3-Ton 14.3 SEER2 Single-Stage Split System — $7,450]
- Option B (High-Efficiency): [e.g., 3-Ton 17.5 SEER2 Inverter Variable-Speed System — $9,650]
Explain equipment cost differences, indoor humidity/noise comfort, and whether existing ductwork supports Option B without static-pressure upgrades.

Sample AI Output

SYSTEM TIER COMPARISON — 3-TON HEAT PUMP
- Option A — 14.3 SEER2 Single-Stage ($7,450): Runs at 100% capacity whenever cooling/heating is called. Reliable, lower upfront repair complexity, ideal for straightforward thermostats and tighter budgets.
- Option B — 17.5 SEER2 Variable Inverter ($9,650): Modulates capacity from 30% to 100% in long low-speed cycles, lowering operating noise and removing 25%–35% more summer humidity.

Duct Compatibility Note: Both options require return static pressure within spec; Option A is slightly more forgiving on older narrow return trunks, whereas Option B delivers peak savings only with unobstructed return airflow.

Ethical & Transparency Checkpoint

Never push variable-speed inverter equipment onto a home with severely undersized return ductwork without quoting the duct fix.

PROMPT 03 • Any LLM

Clarify 10-Year OEM Parts Coverage vs. Contractor Labor Warranty

Use Case & Commercial Purpose: Eliminates anger in Year 4 or Year 6 if a coil or blower motor fails under factory parts warranty while diagnostic/refrigerant labor applies.

Copy-Ready Prompt

Write a crisp 4-sentence Warranty Separation clause for [Client Name]'s HVAC quote distinguishing the 10-year manufacturer OEM parts warranty from our [2-year] installation workmanship & labor warranty.

Sample AI Output

EQUIPMENT & WORKMANSHIP WARRANTY BOUNDARY
Once registered within 60 days (handled by our office at startup), major compressor and heat-exchanger components carry the manufacturer's 10-year OEM parts warranty. Our contractor workmanship guarantee covers installation labor, brazed copper joints, and drain connections at $0 cost for [2 years]. After Year [2], manufacturer-covered part swaps exclude contractor diagnostic trip, recovery, and refrigerant handling labor (unless covered under an optional extended labor plan).

Ethical & Transparency Checkpoint

Confirm who submits the OEM product warranty registration at startup and hand the homeowner their registration certificate.

PROMPT 04 • ChatGPT / Claude / Gemini

Present Undersized Return Duct Findings Without Creating Pressure

Use Case & Commercial Purpose: Shows homeowners exact static-pressure readings proving why adding a second return grille protects their new blower motor.

Copy-Ready Prompt

Write a brief technical note for [Client Name] explaining that static pressure tested at [e.g., 0.85 in. WC vs. 0.50 in. WC target] because the existing [14×20 return grille] is undersized for a [3-ton / 1,200 CFM] unit, and quoting an optional second return drop for [Cost].

Sample AI Output

AIRFLOW & STATIC PRESSURE NOTE
During our inspection, total external static pressure measured [0.85 in. WC] (target for long blower life is <= 0.50 in. WC) because a single [14×20] return feeds a 1,200 CFM system. We can install your new unit onto the existing plenum cleanly, or add a dedicated [12-inch second return drop & grille] for [Cost] to cut fan noise and prevent premature ECM blower strain. Completely your choice—let us know which option you prefer.

Ethical & Transparency Checkpoint

Share real static pressure numbers (in inches of water column) rather than vague 'bad ductwork' claims.

FAQ

Common questions about hvac prompts

Why should HVAC quotes specify AHRI-matched equipment model numbers?

SEER2 efficiency ratings and 10-year OEM warranties apply strictly to factory-matched outdoor condensers and indoor coils listed in the AHRI directory.

What does deep-vacuum <500 microns commissioning mean for homeowners?

Pulling a line set below 500 microns confirms zero air leaks and boils off moisture that would otherwise turn into compressor-destroying acid.

Does a 10-year HVAC manufacturer warranty cover free service labor?

Standard 10-year OEM warranties cover replacement parts only; contractor labor warranties (typically 1–3 years) should be stated separately.

QuoteFast Workflow

Paste your generated scope into a clean PDF proposal.

Once your AI assistant formats the line items, open the Workmanship Warranty Matrix or launch the proposal generator to export PDF/PNG on-device.

Open HVAC Proposal Maker

Explore other prompt packs

View all 18 packs →